Team FLARE | 14 FEBRUARY 2026 | 61.9 MB
发行编号：FLARE-1975
Phoenix II 是 Crane Song 旗下 TDM 插件套件的更新版本，旨在精准模拟磁带机的独特属性。
Phoenix II 支持在 Avid 的 AAX 格式下运行原生（NATIVE）和 DSP 两种模式。测试版现已新增对 AU 和 VST3 格式的支持！Phoenix II 采用 32 位浮点运算，相比初版拥有更低的本底噪声。
设计师 Dave Hill 倾力打造了这款软件，正如他为 ATR Service 备受赞誉的 “Aria” 分立式磁带录音机设计电子电路时那样，对细节给予了同等程度的关注。凭借对模拟电子学的深刻理解，以及作为录音工程师数十年的经验，他研发出了这套极具实用价值且充满音乐性的插件套件。Phoenix II 的处理过程不仅囊括了磁带本身产生的非线性饱和特性，还涵盖了模拟磁带录音机录音/还音电路与均衡曲线之间的相互作用。Phoenix II 是基于 HEDD 技术从底层构建的应用，专门为 Avid 的 AAX 架构进行了工程设计与优化。
Phoenix II 拥有五种不同的模拟磁带特性，用户可通过旋钮选择类型，以便轻松对比；同时也可通过旋钮选择亮度。Gold（黄金）档位的频响色彩较为平直；Sapphire（蓝宝石）音色更亮；Opal（欧泊）音色则更为温暖。通过一个电平旋钮决定 Phoenix II 处理效果融入音频信号的程度，而输入微调旋钮则决定了“磁带的受激励强度”。由于 DSP 处理过程与电平相关，插件改进了输入电平微调控制，并新增了输出微调控制。
输入微调还可用于防止在极少数可能产生削波问题的情况下发生失真，并能提升音轨电平以增加色彩量。这对于接近或达到数字 0dB 即满刻度削波的素材，以及录制电平较低的素材非常有用。当输入微调和输出微调旋钮均处于 0dB（增益无变化）且未添加任何磁带处理效果时，该插件实现了比特级精度，即输出完全等同于输入。
– 运行无需 iLok 驱动程序。
情人节快乐！
系统要求
macOS 10.13 或更高版本
RELEASE NUMBER: FLARE-1975
Phoenix II is an update of Crane Song’s suite of TDM plug-ins designed to emulate the unique properties of a magnetic tape machine.
Phoenix II runs both NATIVE and DSP on Avid’s AAX format. Beta now available with additional AU and VST3 formats! Phoenix II uses 32 bit floating point math and has a lower noise floor than the original release.
Designer Dave Hill has crafted this software with the same attention to detail he used to create the electronics for ATR Service’s much heralded “Aria” discrete tape recorders. His intimate knowledge of analog electronics, as well as decades of experience as a recording engineer has spawned a very useful, musical suite of plug-ins. The Phoenix II process not only incorporates the nonlinear saturation characteristics created by magnetic tape itself, but also includes the interrelation of an analog tape recorder’s record/reproduce electronics and equalization curves. Phoenix II is a ground-up application derived from HEDD technology, and specifically engineered and optimized for Avid’s AAX architecture.
Phoenix II has five different tape-analog characteristics, The type is selected with a switch for easy comparison between the types, and the brightness is also selected with a switch. Gold is the position where the color is approximately flat in frequency response, with Sapphire being a brighter, and Opal being a warmer tonality. A level control determines the amount of the Phoenix II process integrated into the audio signal, and an input trim determines “how hard you hit the tape.” Because the DSP process is level dependent, the input level trim control has been improved and an output trim control has been added.
The input trim can also be used to prevent clipping in the rare cases where clipping may be a problem and bringing up the level of a track for an increased amount of color. This can be useful on material that is hitting close to or at digital zero and on material that has a low recorded level. When the input trim and output trim controls are at 0dB, (no change in gain) and no tape process is being added to the sound, the plug-in is bit accurate, meaning the output exactly matches the input.
– Does not require the iLok driver to run.
HAPPY VALENTINES DAY!
System Requirements
macOS 10.13 or newer
